13 Common Questions About Rotating Shaft Seals.

Release time: 2024-03-25


1. What is a retainer plate (cover plate), and why is it necessary for an all-rubber split seal?
A cover plate is a piece of metal (or another hard material) that is attached after the oil seal is inserted into the housing hole. The cover plate presses on the rear of the oil seal, compressing it into the housing. All-rubber split seals require cover plates because they lack an exterior support to assist sustain the seal, necessitating compression within the housing to guarantee the optimum sealing capabilities.

2. Which way should the lip face when I install my oil seal?
A single lip seal is unidirectional, meaning it only seals in one way. The principal sealing lip should always face or point at the medium that has to be sealed. The media being sealed is often a grease or oil lubricant, but it might also be a chemical media that must remain inside a tank. If the seal is to act as an excluder and prevent contamination, it should face outward toward the contaminant, which might be dirt and dust or chemical washdown.
 

3. Which rubber material should I select for my oil seal?

Proper material selection is critical for effective sealing performance. One of the criteria that influences elastomer selection is the application temperature. Nitrile (NBR) is a popular rubber used in many sealing applications with mild operating conditions and is typically approved for usage at temperatures up to 200 F (continuous). Nitriles are inexpensive and wear resistant, however they harden and/or break when utilized at high temperatures. At temperatures above 200 degrees Fahrenheit, some people choose carboxylated or hydrogenated nitrile (HNBR), which is rated for continuous usage up to 300 degrees Fahrenheit. A fluoroelastomer (FKM) is another form of elastomer that may be utilized at higher temperatures, with a continuous temperature rating of 400 degrees Fahrenheit.

 

4. What lip seal material(s) should I use if my application requires FDA compliance?
The food and beverage business frequently requires FDA-compliant seals. This implies that the lip and case materials must fulfill the FDA's sanitary criteria. FDA-compliant lip materials include FDA silicone, FDA Viton, and various PTFE formulations, to mention a few. If the seal contains a metal housing, FDA compliance mandates the usage of 316SS. Furthermore, much of the equipment in food and beverage applications requires cleaning or steaming while in operation. The seals must endure the cleaning chemicals and high temperatures used in these operations.
 

5. What lip seal material or design would be most suited for a strong chemical application?
Depending on the application, a PTFE lip seal that is compatible with a wide range of chemicals may be required. Furthermore, certain PTFE lip seal designs can survive high pressures and dry operating conditions that typical elastomer seals cannot. PTFE seals are available with and without a metal shell, and they may be fitted in the same groove as a conventional oil seal.
 

6. Should I choose a seal with a metal casing or a rubber outer diameter (OD)?
Seals with a metal casing often have the highest OD interference, or ability to remain within the housing. The trade-off for this exceptionally tight fit is that installing a metal case seal may cause housing damage. Some customers choose rubber OD seals since they do not scratch or harm the housing during installation. Changing to a rubber OD seal may help improve static sealing of prior housing damage caused by a metal-cased seal. Another problem is that typical steel metal casings may corrode or rust over time. This would not be an issue for an all-rubber or metal-encapsulated rubber OD seal.
 

7. I've removed the leaking oil seal from the device. How do I figure out what size oil seal I need?

When replacing a failing oil seal, do not measure the used seal, since this will result in incorrect readings. Aside from the fact that various manufacturers employ different design interferences, used and worn-out oil seals frequently sustain damage during removal. Manufacturers construct oil seals to fit the user's equipment, so all the user has to do is supply the shaft diameter, bore diameter, and bore depth to the seal maker. Check the seal for marks indicating required equipment dimensions.
 

8. How are oil seals measured?
In most cases, users will not need to measure the oil seal. To properly size the seal, users just need to know the equipment's shaft diameter, bore diameter, and bore depth.
Users may need to measure the seal to verify its manufacturing size. An oil seal's most essential dimensions are its interior diameter (ID), exterior diameter (OD), and breadth (height). The seal's ID is not measured directly since it is difficult to do so without straining or changing the lip. The OD of the seal is most properly measured using a particular piece of equipment known as a pi tape.
 

9. Does oil seal thickness matter?
As long as the seal fits the shaft and bore diameters adequately, differing seal widths provide no sealing benefit. If the seal is wider than the bore depth, the only possible concern is interference with the surrounding equipment. In contrast, if the seal width is less than the actual hole depth, this is typically not an issue unless the seal is made entirely of rubber and squeezed by a retainer or cover plate.
 

10. What is the role of the spring in oil seals? 
The spring applies stress to the sealing perimeter and keeps the sealing lip tight against the shaft surface. Some seal designs employ a garter spring design, which exerts pressure all around the shaft. Other seal designs use a finger spring mechanism, which allows for separate finger motion just when needed. Garter springs are susceptible to spring dumping because they often rest inside a molded groove that is not linked to the sealing lip. If the spring detaches during installation.

 

11. How long does an oil seal last?

Seal life on equipment in the field is difficult to predict since operating circumstances are unknown and vary greatly. Furthermore, the applications are typically not ideal (defined as clean lab-type environments, fully lubricated, low speed, ambient temperatures, no pressure, no misalignment or runout, no exposure to chemicals or solids, correctly sized components, and so on), and these factors have a significant impact on seal life.

 

12. When I changed my oil seal, I discovered that the shaft was grooved behind the lip. What's the source of this, and what should I do?
When grooving occurs at the shaft, it is usually due to shaft hardness and/or finish not satisfying industry standards of at least 30 Rockwell C and 10 to 20 microinch Ra. Shaft grooving will occur if there is dirt or contamination in the application, not because of the lip materials themselves. If the shaft is overly soft, certain particles may become trapped behind the lip and groove. It is not suggested to install a new oil seal over shaft grooving, since this may result in leaks.
 

13. Should I glue the broken seal's edges back together during installation?
If the split seal requires a garter spring, there will usually be a hook or screw attachment to draw the two split ends together. Other split seal designs, which include a finger spring, are held together securely by the interference (or press fit) between the seal's OD and the machined bore housing. In any situation, it is normally not suggested to re-glue the split ends of the seals since proper lip alignment is difficult to achieve. Also, the chemical compatibility of the adhesives and lip elastomer must be tested.